Numerical investigation on the electronic components' cooling for different coolants by finite element method

In this study, we conducted a numerical simulation to examine the cooling performance of an aluminum finned heat sink attached to a silicon chip, placed in a chamber of a rectangular cross-section. The heat sink is cooled by convective heat transfer utilizing nine commercially available gaseous coolants, namely air, hydrogen, helium, nitrogen, oxygen, carbon dioxide, freon12 vapor, propane, and ammonia. To select an appropriate coolant for electronic devices in terms of thermal–hydraulic performance, the maximum temperature on the chip domain and the associated pressure drop in the cooling channel as a function of coolant velocity are analyzed for the aforementioned fluids. It has been found that the minimum temperature is recorded for propane and freon12 vapor, which is approximately 31.1°C, for a coolant velocity of 0.5 m/s, but freon12 vapor shows the highest pressure drop, approximately 900 mPa, among all coolants. In the overall velocity regime, hydrogen shows the best cooling performance in terms of both cooling capacity and hydrodynamic characteristics. But considering safety issues, helium can be a better alternative. This comprehensive study provides a better understanding of different coolant performances, which will aid engineers to develop an effective cooling technique to accommodate the inexorably rising power demand.     

Simplification and applicability studies of a hydrogen-air detailed reaction mechanism

The research of hydrogen fuel internal combustion engine (HICE) had great significance facing the challenges of energy and environmental problems. Based on the detailed hydrogen-air reaction mechanism, the pre-mix model of CHEMKIN-Pro software was selected to simplify the detailed mechanism GRI-3.0. The most important elements and reactions was chose to construct framework mechanism firstly based on the sensitivity coefficient for H₂O and NO formation, and additional elements and reactions were added to framework mechanism for complementing the oxidation path of N2 and H₂. A simplified mechanism including 24-step elementary reaction was obtained and the laminar burning velocity calculated by this simplified mechanism matches well with the detailed mechanism in a wide range. This simplified mechanism was also applied in a CFD model which predicted the cylinder instantaneous pressure and NOx emission accurately within a large range of fuel air equivalent ratio. Showing that this mechanism has good applicability.     

径向弹簧蓄能密封结构最大接触应力的有限元分析

为研究径向弹簧蓄能密封结构的密封特性，针对典型径向弹簧蓄能密封结构，分析其密封机制以及O形弯曲金属螺旋弹簧的弹性特性；采用ANSYS有限元分析软件，建立典型弹簧蓄能密封结构的非线性有限元分析模型，对弹簧蓄能密封圈在不同压缩率、不同介质压力下的接触应力进行分析，研究在多种工况下最大接触应力的变化情况。结果表明：压缩率保持不变时，最大接触应力随着介质压力的增大而增大；介质压力保持不变时，随着压缩率的增大，最大接触应力先增大再减小。对压缩率、介质压力与最大接触应力的关系进行曲线拟合，可用于指导弹簧蓄能密封结构的精确设计。     

Interconnected SiC–Si network reinforced Al–20Si composites fabricated by high pressure solidification

The microstructures and mechanical properties of the interconnected SiC–Si network reinforced Al–20Si composites solidified under high pressures were investigated. The results demonstrate that the complete interconnected SiC–Si network can be obtained by high pressure solidification, and the connected micron-sized pores are uniformly distributed in the interconnected SiC–Si network. The compressive strength and microhardness of the SiC/Al–20Si composites solidified under 3 GPa were 723 MPa and 229 HV_0.05, respectively. Furthermore, the fracture process of SiC/Al–20Si composites was studied by in situ TEM tensile testing. The result shows that the crack first initiated and propagated at the Al/Si interface under an external load, and the SiC particles in the interconnected SiC–Si network can effectively hinder the crack propagation, thus enhancing the strength.     

Effects of external light load on posture and foot pressure distribution in young adults: A pilot study

Holding an asymmetrical load, like a rucksack, grocery bag, or travel backpack, is a part of daily and occupational activities. This pilot study was aimed to determine the effects of light, asymmetrical, handheld load on the body posture and foot pressure distribution in young adults. Thirteen young volunteers, free of any injury or pain, took part in the study (aged 21.53 ± 1.10 years). All the study participants were right-handed. An additional load (4 kg, placed in the rucksack) was asymmetrically held in each hand while standing still. For evaluation of the posture and foot pressure distribution, the investigation focused on three positions, i.e., no-load, a rucksack in the right hand, a rucksack in the left hand. We used a surface topography system and force platform for evaluation of the body posture and foot pressure examination, respectively. The results showed that the main changes in the body posture caused by an external load application manifested in trunk imbalance. The trunk was shifted in the direction opposite to the load. Trunk imbalance changes were statistically significant in all three comparisons (p = 0.001). Interestingly, changes in the rotations and lateral deviation seem to be dependent on the hand dominance. Greater foot pressure was observed on the loaded limb (p < 0.01), and highly significant differences were noted between the left and right foot in both loaded postures (p < 0.001). Further research needs to be done to check if lateralization is connected with body posture while holding an external load.     

Metabolic Profiling of VOCs Emitted by Bacteria Isolated from Pressure Ulcers and Treated with Different Concentrations of Bio-AgNPs

Considering the advent of antibiotic resistance, the study of bacterial metabolic behavior stimulated by novel antimicrobial agents becomes a relevant tool to elucidate involved adaptive pathways. Profiling of volatile metabolites was performed to monitor alterations of bacterial metabolism induced by biosynthesized silver nanoparticles (bio-AgNPs). Escherichia coli, Enterococcus faecalis, Klebsiella pneumoniae and Proteus mirabilis were isolated from pressure ulcers, and their cultures were prepared in the presence/absence of bio-AgNPs at 12.5, 25 and 50 µg mL⁻¹. Headspace solid phase microextraction associated to gas chromatography–mass spectrometry was the employed analytical platform. At the lower concentration level, the agent promoted positive modulation of products of fermentation routes and bioactive volatiles, indicating an attempt of bacteria to adapt to an ongoing suppression of cellular respiration. Augmented response of aldehydes and other possible products of lipid oxidative cleavage was noticed for increasing levels of bio-AgNPs. The greatest concentration of agent caused a reduction of 44 to 80% in the variety of compounds found in the control samples. Pathway analysis indicated overall inhibition of amino acids and fatty acids routes. The present assessment may provide a deeper understanding of molecular mechanisms of bio-AgNPs and how the metabolic response of bacteria is untangled.     

Investigation of the piezoelectric and anti-reduction properties of (Ba,Ca) (Ti,Sn, Hf) textured ceramics prepared under low oxygen partial pressure conditions at low sintering temperatures

Multilayer piezoelectric ceramics must be sintered in a reducing atmosphere, preventing oxidation of the inner base metal. Plate-like textured (Ba, Ca)(Ti, Sn, Hf)O₃ ceramics with a <001> preferred orientation were successfully developed at a low oxygen partial pressure (PO₂:10^?8 atm) using a BaTiO₃ (BT) template with sintering temperatures < 1300 °C, which is beneficial for multilayer applications using base metal co-firing with ceramics. When adding the 3 wt% BT template, the proposed samples had a Lottgering factor of 84 %, piezoelectric coefficients d₃₃ = 324 pC/N, -d₃₁ = 122 (pC/N), and Q_m = 452, and the strain values increased from 0.07 % for the randomly oriented ceramics to 0.115 % at 20 kV/cm for the textured ceramics, confirming that the texturing behavior assisted the grain growth and improved both the soft and hard behaviors and insulation resistance of the proposed lead-free ceramics. These findings make a significant contribution to the production of high-power piezoelectric components.     

A theoretical and experimental study of phosphate ester inhibitors for AISI 1018 in carbon dioxide-saturated 3.5 wt% NaCl solution

Phosphate ester was investigated as a corrosion inhibitor for AISI 1018 carbon steel in carbon dioxide-saturated chloride solutions at different temperatures and pressures. The corrosion tests were realized by electrochemical techniques, weight loss measurements, bubble tests, and a high-pressure/high-temperature autoclave system. The corrosion tests demonstrated that the investigated molecule is an excellent corrosion inhibitor. The inhibiting effect is even bigger at high pressure and temperature than at atmospheric pressure and room temperature. The thermodynamic parameters were calculated and determined to obey the Langmuir isotherm. Polarization studies revealed that the evaluated inhibitor is a mixed type.     

Fast filling strategy of type III on-board hydrogen tank based on time-delayed method

In order to study the fast filling problem of the type III on-board hydrogen tank, a 3D computational fluid dynamics (CFD) simulation model is proposed. Several simulation calculations are completed to simulate the fast filling process under different initial conditions. In order to control the temperature rise during the fast filling process, the effects of different mass flow rates are studied. Based on the control of mass flow rate, various time-delayed filling strategies for different conditions are proposed to meet the requirement of shortening the filling time as much as possible without exceeding the maximum temperature limit. It is found that if the delay duration is determined, how the filling time is allocated has little effect on the final temperature rise. The proposed strategy can complete the filling within 155s in a general environment, which saves 62% of the time compared with the filling with constant mass flow rate. This research provides the theoretical basis and technical support for mass flow control strategies of fast filling in the hydrogen refueling stations and has guiding significance for the actual filling process of large-capacity hydrogen tanks.